Tag Archives: kazmi elecom

DOFFLER 32BH31-T2 LED TV

DOFFLER 32BH31-T2 is a 32 inches HD Ready LED TV with a resolution of 1366×768. 32BH31-T2 is a non-smart tv. 32BH31-T2 led TV has all the latest features and connectivity ports as HDMI port and USB port, Dual Audio Video with a 60 Hz refresh rate. It has a powerful sound output system. Its aspect ratio is 16:09 and its dynamic ratio is 150000:1.

Its view angle is horizontal: 170 degrees and vertical: 160 degrees. 32BH31-T2 has additional edge led technology, smart power saving, DOFFLER noise reduction, intelligent picture technology, eye-safe t matrix, brightness is 250 cd/m2 and response time is 5 ms. DOFFLER Software file is given below for the technician’s support. For more DOFFLER Software collection visit here.

General Specifications & Features:

Make: DOFFLER

Model: 32BH31-T2

Display Size: “32

Storage Memory: MB

HD Technology: HD

Panel: HD

No of HDMI Ports:

No of USB Ports:

No of AV Ports:

Speaker Output RMS:

Power Requirement: AC 110 – 240 V, 50/60 Hz

Power Consumption: W, 0.5 W (Standby)

Software Type: Backup Dump

Software Name:

Main Board: TP.S512.PB83

Note: Following given Software is backup dump. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the Software.If you are new and do not have enough knowledge of loading or installing software/firmware or dump files then read here first.

For video tutorials, visit “Kazmi Elecom” my youtube channel.

DEXP F55D7000K LED TV

DEXP F55D7000K is a 55 inches HD Ready LED TV with a resolution of 1366×768. F55D7000K is a non-smart tv. F55D7000K led TV has all the latest features and connectivity ports as HDMI port and USB port, Dual Audio Video with a 60 Hz refresh rate. It has a powerful sound output system. Its aspect ratio is 16:09 and its dynamic ratio is 150000:1.

Its view angle is horizontal: 170 degrees and vertical: 160 degrees. F55D7000K has additional edge led technology, smart power saving, digital noise reduction, intelligent picture technology, eye-safe t matrix, brightness is 250 cd/m2 and response time is 5 ms. DEXP Software file is given below for the technician’s support. For more DEXP Software collection visit here.

General Specifications & Features:

Make: DEXP

Model: F55D7000K

Display Size: “55

Storage Memory: MB

HD Technology: HD

Panel: HD

No of HDMI Ports:

No of USB Ports:

No of AV Ports:

Speaker Output RMS:

Power Requirement: AC 110 – 240 V, 50/60 Hz

Power Consumption: W, 0.5 W (Standby)

Software Type: Backup Dump

Software Name:

Main Board: TP.MS3663S.PC821

Note: Following given Software is backup dump. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the Software.If you are new and do not have enough knowledge of loading or installing software/firmware or dump files then read here first.

For video tutorials, visit “Kazmi Elecom” my youtube channel.

DEXP 16A3000 LED TV

DEXP 16A3000 is a 16 inches HD Ready LED TV with a resolution of 1366×768. 16A3000 is a non-smart tv. 16A3000 led TV has all the latest features and connectivity ports as HDMI port and USB port, Dual Audio Video with a 60 Hz refresh rate. It has a powerful sound output system. Its aspect ratio is 16:09 and its dynamic ratio is 150000:1.

Its view angle is horizontal: 170 degrees and vertical: 160 degrees. 16A3000 has additional edge led technology, smart power saving, digital noise reduction, intelligent picture technology, eye-safe t matrix, brightness is 250 cd/m2 and response time is 5 ms. DEXP Software file is given below for the technician’s support. For more DEXP Software collection visit here.

General Specifications & Features:

Make: DEXP

Model: 16A3000

Display Size: “16

Storage Memory: MB

HD Technology: HD

Panel: HD

No of HDMI Ports:

No of USB Ports:

No of AV Ports:

Speaker Output RMS:

Power Requirement: AC 110 – 240 V, 50/60 Hz

Power Consumption: W, 0.5 W (Standby)

Software Type: Backup Dump

Software Name:

Main Board: CVMV29L-F

Note: Following given Software is backup dump. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the Software.If you are new and do not have enough knowledge of loading or installing software/firmware or dump files then read here first.

For video tutorials, visit “Kazmi Elecom” my youtube channel.

DEXP H24F7000C LED TV

DEXP H24F7000C is a 24 inches HD Ready LED TV with a resolution of 1366×768. H24F7000C is a non-smart tv. H24F7000C led TV has all the latest features and connectivity ports as HDMI port and USB port, Dual Audio Video with a 60 Hz refresh rate. It has a powerful sound output system. Its aspect ratio is 16:09 and its dynamic ratio is 150000:1.

Its view angle is horizontal: 170 degrees and vertical: 160 degrees. H24F7000C has additional edge led technology, smart power saving, digital noise reduction, intelligent picture technology, eye-safe t matrix, brightness is 250 cd/m2 and response time is 5 ms. DEXP Software file is given below for the technician’s support. For more DEXP Software collection visit here.

General Specifications & Features:

Make: DEXP

Model: H24F7000C

Display Size: “24

Storage Memory: MB

HD Technology: HD

Panel: HD

No of HDMI Ports:

No of USB Ports:

No of AV Ports:

Speaker Output RMS:

Power Requirement: AC 110 – 240 V, 50/60 Hz

Power Consumption: W, 0.5 W (Standby)

Software Type: Backup Dump

Software Name:

Main Board: JUC7.820.00267398

Note: Following given Software is backup dump. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the Software.If you are new and do not have enough knowledge of loading or installing software/firmware or dump files then read here first.

For video tutorials, visit “Kazmi Elecom” my youtube channel.

MAXRON D141158_008 DVR

MAXRON D141158_008 DVR backup file is posted here in this post for the support of technicians to recover or repair DVR/NVR. In most of the cases video recorder is stuck on the startup or logo screen and does not completely boot due to software malfunctioning or bios problems and in some other cases, DVR/NVR may not power on or have no display but only on standby/red ligh. In such cases, there may be a software issue or hardware issue. So, first of all, if the video recorder is on standby/red light only then check the core voltage and ensure that all measurements are perfect and the main system IC is also normal then load the backup file.

MAXRON D141158_008 DVR backup is saved from working DVR/NVR. Be careful when writing backup files. Make sure that the main board or chassis are same as you require and if possible verify the main processor. You should first keep the backup of old software and then write another. Always check the software backup size and flash memory size which will be the same in size. DVR/NVR channel capacity may be different in some cases but the main board and processor are the same. In these cases, you can write a backup file if there is no other option.

Technical Specifications of MAXRON D141158_008 DVR:

Manufacturer/Make/Brand Name:

DVR/NVR Model:

Chassis/Main Board:

Chipset/System IC/Processor:

Channel/Ports:

Software Version:

SPI Flash Memory:

Note: The following firmware is a backup file and can be written by a programming tool or can be loaded by a loader tool. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the firmware. First, check and verify the main board then install software. If you are new and do not have enough knowledge of loading/installing software/firmware or dump files, or facing any issues during firmware installation then visit and read here first.

How to Download:

Download your required DVR/NVR backup firmware/software and then extract it you will get the folder. Now copy the files to USB or load them with a programmer. For more Details about the download process watch the video Click Here

MAXRON D141158_008 DVR Software Backup File Free Download.

For video tutorials, visit “Kazmi Elecom” my YouTube channel.

HVR508 VER1.1 20171031 DVR

HVR508 VER1.1 20171031 DVR backup file is posted here in this post for the support of technicians to recover or repair DVR/NVR. In most of the cases video recorder is stuck on the startup or logo screen and does not completely boot due to software malfunctioning or bios problems and in some other cases, DVR/NVR may not power on or have no display but only on standby/red ligh. In such cases, there may be a software issue or hardware issue. So, first of all, if the video recorder is on standby/red light only then check the core voltage and ensure that all measurements are perfect and the main system IC is also normal then load the backup file.

HVR508 VER1.1 20171031 DVR backup is saved from working DVR/NVR. Be careful when writing backup files. Make sure that the main board or chassis are same as you require and if possible verify the main processor. You should first keep the backup of old software and then write another. Always check the software backup size and flash memory size which will be the same in size. DVR/NVR channel capacity may be different in some cases but the main board and processor are the same. In these cases, you can write a backup file if there is no other option.

Technical Specifications of HVR508 VER1.1 20171031 DVR:

Manufacturer/Make/Brand Name:

DVR/NVR Model:

Chassis/Main Board:

Chipset/System IC/Processor:

Channel/Ports:

Software Version:

SPI Flash Memory:

Note: The following firmware is a backup file and can be written by a programming tool or can be loaded by a loader tool. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the firmware. First, check and verify the main board then install software. If you are new and do not have enough knowledge of loading/installing software/firmware or dump files, or facing any issues during firmware installation then visit and read here first.

How to Download:

Download your required DVR/NVR backup firmware/software and then extract it you will get the folder. Now copy the files to USB or load them with a programmer. For more Details about the download process watch the video Click Here

HVR508 VER1.1 20171031 DVR Software Backup File Free Download.

For video tutorials, visit “Kazmi Elecom” my YouTube channel.

HVR504 V3.3 DVR

HVR504 V3.3 DVR backup file is posted here in this post for the support of technicians to recover or repair DVR/NVR. In most of the cases video recorder is stuck on the startup or logo screen and does not completely boot due to software malfunctioning or bios problems and in some other cases, DVR/NVR may not power on or have no display but only on standby/red ligh. In such cases, there may be a software issue or hardware issue. So, first of all, if the video recorder is on standby/red light only then check the core voltage and ensure that all measurements are perfect and the main system IC is also normal then load the backup file.

HVR504 V3.3 DVR backup is saved from working DVR/NVR. Be careful when writing backup files. Make sure that the main board or chassis are same as you require and if possible verify the main processor. You should first keep the backup of old software and then write another. Always check the software backup size and flash memory size which will be the same in size. DVR/NVR channel capacity may be different in some cases but the main board and processor are the same. In these cases, you can write a backup file if there is no other option.

Technical Specifications of HVR504 V3.3 DVR:

Manufacturer/Make/Brand Name:

DVR/NVR Model:

Chassis/Main Board:

Chipset/System IC/Processor:

Channel/Ports:

Software Version:

SPI Flash Memory:

Note: The following firmware is a backup file and can be written by a programming tool or can be loaded by a loader tool. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the firmware. First, check and verify the main board then install software. If you are new and do not have enough knowledge of loading/installing software/firmware or dump files, or facing any issues during firmware installation then visit and read here first.

How to Download:

Download your required DVR/NVR backup firmware/software and then extract it you will get the folder. Now copy the files to USB or load them with a programmer. For more Details about the download process watch the video Click Here

HVR504 V3.3 DVR Software Backup File Free Download.

For video tutorials, visit “Kazmi Elecom” my YouTube channel.

HISONY 5004E HI3515 DVR

HISONY 5004E HI3515 DVR backup file is posted here in this post for the support of technicians to recover or repair DVR/NVR. In most of the cases video recorder is stuck on the startup or logo screen and does not completely boot due to software malfunctioning or bios problems and in some other cases, DVR/NVR may not power on or have no display but only on standby/red ligh. In such cases, there may be a software issue or hardware issue. So, first of all, if the video recorder is on standby/red light only then check the core voltage and ensure that all measurements are perfect and the main system IC is also normal then load the backup file.

HISONY 5004E HI3515 DVR backup is saved from working DVR/NVR. Be careful when writing backup files. Make sure that the main board or chassis are same as you require and if possible verify the main processor. You should first keep the backup of old software and then write another. Always check the software backup size and flash memory size which will be the same in size. DVR/NVR channel capacity may be different in some cases but the main board and processor are the same. In these cases, you can write a backup file if there is no other option.

Technical Specifications of HISONY 5004E HI3515 DVR:

Manufacturer/Make/Brand Name:

DVR/NVR Model:

Chassis/Main Board:

Chipset/System IC/Processor:

Channel/Ports:

Software Version:

SPI Flash Memory:

Note: The following firmware is a backup file and can be written by a programming tool or can be loaded by a loader tool. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the firmware. First, check and verify the main board then install software. If you are new and do not have enough knowledge of loading/installing software/firmware or dump files, or facing any issues during firmware installation then visit and read here first.

How to Download:

Download your required DVR/NVR backup firmware/software and then extract it you will get the folder. Now copy the files to USB or load them with a programmer. For more Details about the download process watch the video Click Here

HISONY 5004E HI3515 DVR Software Backup File Free Download.

For video tutorials, visit “Kazmi Elecom” my YouTube channel.

HiLook DVR-116G-F1 DVR

HiLook DVR-116G-F1 DVR backup file is posted here in this post for the support of technicians to recover or repair DVR/NVR. In most of the cases video recorder is stuck on the startup or logo screen and does not completely boot due to software malfunctioning or bios problems and in some other cases, DVR/NVR may not power on or have no display but only on standby/red light. In such cases, there may be a software issue or hardware issue. So, first of all, if the video recorder is on standby/red light only then check the core voltage and ensure that all measurements are perfect and the main system IC is also normal then load the backup file.

HiLook DVR-116G-F1 DVR backup is saved from working DVR/NVR. Be careful when writing backup files. Make sure that the main board or chassis are same as you require and if possible verify the main processor. You should first keep the backup of old software and then write another. Always check the software backup size and flash memory size which will be the same in size. DVR/NVR channel capacity may be different in some cases but the main board and processor are the same. In these cases, you can write a backup file if there is no other option.

Technical Specifications of HiLook DVR-116G-F1 DVR:

Manufacturer/Make/Brand Name: HiLook

DVR/NVR Model: DVR-116G-F1

Chassis/Main Board: DS-7116HGHI-F1N

Chipset/System IC/Processor: Hisilicon

Channel/Ports: 16

Software Version:

SPI Flash Memory: 16 MB

Interface: VGA, HDMI, RCA, RJ45, BNC

Power Supply Input: 12C-4Amp

Power Consumption: 15w without HDD

Caution: 

All the pictures and specification details related to the HiLook DVR-116G-F1 DVR in this post are for reference only. If you are a user and do not have any repair experience, it is better to visit the nearest technician first without installing the Backup File. Sometimes, the fault is different based on the visual observations. So, please do not try it at home.

HiLook DVR-116G-F1 DVR Version Upgrade:

Please note that the installed version in this DVR is the final version that will operate normally. Mostly the manufacturer releases updates to fix the bugs in the previous version or adds some new features and applications for customer satisfaction and smooth working of the DVRs. Please note that the following given HiLook DVR-116G-F1 DVR program backup file is not for upgrade purposes.

Pros:

There are some advantages to installing the given HiLook DVR-116G-F1 DVR backup dump file. A few benefits are described below:

• The dead DVR can be recovered and operational by loading the given Backup Dump File
• Money saving instead of changing the DVR mainboard
• Time-saving instead of arranging a new DVR board
• The customer satisfaction to do an urgent job by installing the backup file

Cons:

There may be some disadvantages to writing the given HiLook DVR-116G-F1 DVR backup dump file. A few drawbacks are described below:

• The working DVR may go to the standby position or dead
• The DVR manufacturer logo and some features may change
• Video channels may be out of order
• No display for some cameras

Note: The following HiLook DVR-116G-F1 DVR program is a backup file that can be written by a programming tool or loaded by a loader tool. First, read the original Flash file and save it. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the firmware. First, check and verify the main board then install software. If you are new and do not have enough knowledge of loading/installing software/firmware or dump files, or facing any issues during firmware installation then visit and read here first.

How to Download:

Download your required DVR/NVR backup firmware/software and then extract it you will get the folder. Now copy the files to USB or load them with a programmer. For more Details about the download process watch the video Click Here

HiLook DVR-116G-F1 DVR Software Backup File Free Download.

HiLooK DVR-108G-F1 DS-80257_P REV1.2 DVR

HiLooK DVR-108G-F1 DS-80257_P REV1.2 DVR backup file is posted here in this post for the support of technicians to recover or repair DVR/NVR. In most of the cases video recorder is stuck on the startup or logo screen and does not completely boot due to software malfunctioning or bios problems and in some other cases, DVR/NVR may not power on or have no display but only on standby/red ligh. In such cases, there may be a software issue or hardware issue. So, first of all, if the video recorder is on standby/red light only then check the core voltage and ensure that all measurements are perfect and the main system IC is also normal then load the backup file.

HiLooK DVR-108G-F1 DS-80257_P REV1.2 DVR backup is saved from working DVR/NVR. Be careful when writing backup files. Make sure that the main board or chassis are same as you require and if possible verify the main processor. You should first keep the backup of old software and then write another. Always check the software backup size and flash memory size which will be the same in size. DVR/NVR channel capacity may be different in some cases but the main board and processor are the same. In these cases, you can write a backup file if there is no other option.

Technical Specifications of HiLooK DVR-108G-F1 DS-80257_P REV1.2 DVR:

Manufacturer/Make/Brand Name:

DVR/NVR Model:

Chassis/Main Board:

Chipset/System IC/Processor:

Channel/Ports:

Software Version:

SPI Flash Memory:

Note: The following firmware is a backup file and can be written by a programming tool or can be loaded by a loader tool. Kazmi Elecom Team is not responsible for any type of damage/loss as a result of uploading/downloading the firmware. First, check and verify the main board then install software. If you are new and do not have enough knowledge of loading/installing software/firmware or dump files, or facing any issues during firmware installation then visit and read here first.

How to Download:

Download your required DVR/NVR backup firmware/software and then extract it you will get the folder. Now copy the files to USB or load them with a programmer. For more Details about the download process watch the video Click Here

HiLooK DVR-108G-F1 DS-80257_P REV1.2 DVR Software Backup File Free Download.

For video tutorials, visit “Kazmi Elecom” my YouTube channel.